0
Owner's of the Coleman Tent 2000004659 gave it a score of 0 out of 5. Here's how the scores stacked up:
11A
Grommet
Rainfly
Pole
Fig. 11
11B
Black Main
Pole
11C
11D
Guyline
5. Insert metal tip of black rainfly pole into metal grommet located on front
seams of tent (Fig. 11 & 11A). Gradually apply pressure to other end of pole
to form an arch & insert metal tip into grommet.
6. Attach hook & loop fasteners, located on seams of the underside of Rainfly,
around the black main poles, to secure. (Fig. 11B)
7. Clip hooks on elastic cords, on the front and back corners of Rainfly, onto
metal loops at front and back corners
of tent. (Fig. 11C)
8. Stretch guylines until taut, then secure
with stakes. (Fig. 11D)
STITCH LINE
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensation
will form on the inside of your tent. Condensation is caused by water
vapor from your breath, perspiration, or any wet clothing inside the
tent. It is NOT LEAKAGE through the shelter fabric. It can be minimized
by removing wet clothing from your shelter and by providing good
ventilation through the tent.
• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off tree
limbs can cause damage to the tent fabric and its coating resulting in
leaks or loss of flame-resistant properties.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. NEVER PULL ON
THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
• Tent poles should not be left telescoped together during storage.
• Do not leave your tent set-up for weeks at a time. Be aware that
exposure to ultraviolet rays from the sun can seriously damage material
and/or cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn
if left in continuous contact with any flame source. The application of any foreign
substance to the tent fabric may render the flame-resistant properties ineffective.
CAUTION: All “springs” must be removed from sleeves before tearing down
tent to avoid damage to the tent fabric or part. To avoid injury, carefully roll up
“springs”. Keep out of reach of children. Store rolled “springs” in bag
with stakes.
To Store
1. All “springs” must be rolled up and placed in bag with stakes.
2. All poles and stakes must be placed in the storage bag to prevent damage
to the fabric items placed in the carry case.
3. Make sure tent is clean and dry before placing in carry case.
4. Remove rainfly, spread out on floor of tent, then unzip door & vents before
taking tent down for storage.
5. Neatly fold tent to width of pole storage bag, place on tent, roll tightly, and
place in carry case.
6. Store in a clean, dry area.
Electrical Cord Access
1. Unzip the access panel in the lower left
corner of tent and bring in an
electrical cord.
NOTE: Use only UL approved cords rated
for outdoor usage. (Fig. 17)
Fig. 17
Self-rolling Windows
CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury.
Keep out of reach of children.
NOTE: Carefully unroll metal “springs” stored in bag with stakes. The color
marking on each “spring” should match the color of the fabric “flag” sewn to
the window or door sleeve opening. (Fig. 12)
1. Locate sleeve(s) in window panel, open hook & loop fastener; then insert
“spring(s)” with matching color marking. (Fig. 12 & 13)
NOTE: When inserting into the sleeve(s), the color marking on the “spring(s)”
should always face the operator.
2. Close hook & loop fastener to secure.
3. Before unzipping and opening the window, push in at top to engage
“spring(s)” to activate the self-rolling feature. (Fig. 14)
4. Unzip to allow the window panel to roll down automatically; zip back to
close window panel. (Fig. 15 & 16)
NOTE: Repeat steps above for inserting the color matching “spring(s)” into
sleeve(s) for the rest of the windows.
Fig. 12
Sleeve
Color “Flag”
Push in at top
to engage “spring(s)”
Fig. 14
Window Panel
Sleeves
Fig. 15
Door
Window
Panel
Fig. 16
Color
Dot
Fig. 13
Color
“Flag”
4010006299 (ECN20018377-02)
The Coleman Company, Inc. • 3600 North Hydraulic • Wichita, Kansas 67219 U.S.A.
1-800-835-3278 • www.coleman.com
MADE IN CHINA
© 2011 The Coleman Company, Inc. All rights reserved.
Coleman
®
, , and are registered trademarks of
The Coleman Company, Inc.
Find Your Products By Category
Please Login
